The power supply needs to be disconnected during the resistance check. At this time， the principle can be used to measure， and then the resistance value can be measured， so that the fault point can be analyzed accordingly. These introductions I believe you have mastered a lot of basics.
To understand the operation of the mechanism， it mainly depends on whether it is normal and whether there is noise during use. When a fault is found， it needs to be eliminated in time， so as to ensure the normal operation and use of the machine. It is usually necessary to disassemble or adjust the slewing mechanism during installation. In this case it is necessary to ensure that the centerline of the slewing mechanism on the reducer is parallel to the centerline of the gear， and of course the meshing clearance must be appropriate. If this is not appropriate， then the machine will not work properly.
FoggiaThere are problems with the hydraulic torque converter and compensation system， such as weak hydraulic torque converter， power shift failure， high oil temperature， insufficient hydraulic oil quantity， improper pressure regulation， insufficient back pressure. Check the quality of torque converter oil (whether hydraulic transmission oil is misused)， dosage， back pressure valve and their set pressure value. Power shift failure. Quick return valve， power transmission valve， and directional valve are stuck Internal leakage and serious oil pollution. Check the cause of valve jamming and eliminate it accordingly. Filter or replace the hydraulic oil. If the oil temperature rises too much， check if there are any problems with the cooler. Check the quality of the hydraulic oil. Common problems with aluminum alloy elevators of brand names. After cleaning the elevator， the elevator body should be cleaned. Some residual materials left during the lifting process may corrode the elevator.
When using a hydraulic lift， check the connection of each part during use， and tighten it in time if there is any looseness. All the connecting shafts need to use cotter pins， the purpose is to be able to fully meet the needs， and then can be used better.
SalagaSo celebrities can choose these lifting stages when they have a concert， and these stages can highlight the atmosphere of the concert， and make more fans very satisfied with it. But every time we hold a concert， we have to rebuild a new machine? Maybe not because the leasing business of these machines is relatively good in the market now， so when we need them， we can directly lease the corresponding staff to complete the use of the products， and there is no need to buy a new one at all. After all， both the new and the old are for us to use and perform better.
At the same time，FoggiaLifting platform truck handle， pay attention during use to prevent damage to hands， feet and clothes.
In this case， it is necessary to check all the wires and cables used frequently to ensure that they are not damaged. When there is bandaging or damage， the parts must be replaced in time. I believe that many people have encountered the phenomenon of overheating of the motor. In this case， and then continue to use it after troubleshooting， so that the motor shaft can run smoothly and the effect is good.
Everyone knows that hydraulic lifts are used in many industries， and the stability of the machine must be ensured when using them. If the machine is unstable， so what details of the hydraulic lift cannot be ignored during use?
When performing cylinder maintenance， it is necessary to check if there is any oil in the rod and plastic air pipe inside but the oil should not be too much. If there is too much oil，At this time， the sealing components of the oil cylinder may also fail in this situation. Of course， if the oil volume in the mailbox is too full， it will also affect its effectiveness， so it is necessary to pay attention to safety.
So celebrities can choose these lifting stages when they have a concert， and these stages can highlight the atmosphere of the concert， and make more fans very satisfied with it. But every time we hold a concert， we have to rebuild a new machine? Maybe not， because the leasing business of these machines is relatively good in the market now， so when we need them， we can directly lease the corresponding staff to complete the use of the products， and there is no need to buy a new one at all. After all， both the new and the old are for us to use and perform better.
knowledgeAt the same time， pay attention during use to prevent damage to hands， feet and clothes.
In this case， it is necessary to check all the wires and cables used frequently to ensure that they are not damaged. When there is bandaging or damage， the parts must be replaced in time. I believe that many people have encountered the phenomenon of overheating of the motor. In this case， it is necessary to stop in time， and then continue to use it after troubleshooting， so that the motor shaft can run smoothly and the effect is good.
The power supply needs to be disconnected during the resistance check. At this time， the principle can be used to measure， and then the resistance value can be measured， so that the fault point can be analyzed accordingly. These introductions， I believe you have mastered a lot of basics.
When celebrities hold concerts， we all need to use the lifting stage， because if there is no stage to highlight the concert， the atmosphere will be relatively ordinary， and it will appear full of local flavor. If there is such an elevating stage， then it can create certain surprises for the fans. For example， the singer can stand in the elevating platform and make preparations at any time. After the backstage operation is successful ， The singer will walk up from the lifting platform， which is a very surprising thing， and the stage effect produced in this way may be better， which improves the atmosphere of the concert for us.
Fair priceWith the above detailed introduction， I believe that everyone has a comprehensive understanding and understanding of the use of hydraulic lifts， and these details cannot be ignored in the process of use.
With the continuous development of the times， electric lifting platform trucks are now widely used in many industries because they facilitate the transportation or loading and unloading of goods between floors. They are now widely used in many fields. So what should be paid attention to during the use of electric lifting platform vehicles?
There are many details that cannot be ignored when using the hydraulic lifting platform truck. It mainly uses an external power supply so the staff need to master its operation knowledge when operating. This is the basic content. At the same time， it is also necessary to master the corresponding emergency treatment plan. It is also necessary to check the corresponding route when processing， which is the basic content. So in addition to this， what preparations need to be mastered during the use of hydraulic lifts?
FoggiaIn this case， it is necessary to check all the wires and cables used frequently to ensure that they are not damaged. When there is bandaging or damage， the parts must be replaced in time. I believe that many people have encountered the phenomenon of overheating of the motor. In this case， it is necessary to stop in time， and then continue to use it after troubleshooting， so that the motor shaft can run smoothly and the effect is good.
When using a hydraulic lift， check the connection of each part during use， and tighten it in time if there is any looseness. All the connecting shafts need to use cotter pins， the purpose is to be able to fully meet the needs， and then can be used better.
When the hydraulic lifting platform vehicle breaks down， it takes time to make corresponding preparations. At this time，FoggiaLifting platform truck 16 meters， it is necessary to give feedback in time or contact the manufacturer. If the voltage file is used to detect the hydraulic lifting platform vehicle， in this case it is necessary to turn on the power supply. The circuit schematic diagram is used to measure the electricity. At this time， the voltage value can be measured， and the voltage value can also be used to understand where the fault point occurs. Therefore in this case， it is necessary to learn to analyze.
